Finally, you must wait for the following message ''Accepted'' to appear on the LCD, and then close the front cover of your Brother MFC-8660DN Multifunction Printer. In the next step of the new drum unit installation, you must push and hold down the button until the following message ''Replace Drum'' appears on the LCD, and then confirm the new drum unit installation by pressing.
Drum near end on brother mfc 8860dn install#
Now, you must insert the toner cartridge into the new drum unit until the blue lock release lever is automatically raised, and then install the assembled consumable components into the printer. Then, you must carefully unpack the new drum unit, but avoid touching the photoconductive drum, which is located on its top side. After that, you must detach the still useable toner cartridge by pulling it out of the exhausted drum unit while pressing down the blue lock release lever on the right. The replacement procedure is included below.Initially, you must open the front cover of your Brother MFC-8660DN Multifunction Printer, and then take the exhausted drum unit out by carefully pulling it towards you.
![drum near end on brother mfc 8860dn drum near end on brother mfc 8860dn](https://i.ytimg.com/vi/XjsRBqhC7rc/maxresdefault.jpg)
The drum unit replacement procedure is relatively simple, and you won't need any special tools for its successful execution.
![drum near end on brother mfc 8860dn drum near end on brother mfc 8860dn](https://www.u-buy.com.ua/productimg/?image=aHR0cHM6Ly9tLm1lZGlhLWFtYXpvbi5jb20vaW1hZ2VzL0kvNzFMSmVwQ0hSMUwuX0FDX1NMMTUwMF8uanBn.jpg)
Herein, you should purchase a new drum unit and install it in your MFC-8860DN soon after the initial appearance of the ''Drum Near End'' warning message. An exhausted drum unit could still be used for a certain limited number of new prints, but even so, that is not recommended because the print quality will be drastically decreased, and a variety of print quality problems will appear very soon. You have to replace the drum unit in this situation, because the above warning message is indicating that the installed drum unit is exhausted. Therefore, the number of pages printed with the currently installed drum unit is constantly monitored by the precise built-in system, and once the maximal prints number has been reached, the system will display the following warning message ''Drum Near End'' on the control LCD of your printer. However, the drum unit is also a consumable printer component, and because of that fact, it must be replaced after a certain number of new prints. The drum unit installed in your Brother MFC-8860DN Multifunction Printer has a bigger resource/longer lifespan than the installed toner cartridge. In order to complete the current replacement procedure, you must make sure that the following message ''Accepted'' has appeared on the LCD, and then finalize the procedure by closing the front cover of your Brother MFC-8860DN Multifunction Printer.
![drum near end on brother mfc 8860dn drum near end on brother mfc 8860dn](https://i.ytimg.com/vi/XjsRBqhC7rc/mqdefault.jpg)
Once the new drum unit along with the securely attached toner cartridge are appropriately installed, you must push and hold down the button until the following message ''Replace Drum?'' appears on the LCD, and then press to confirm the new drum unit installation, and resp. dcp-7030, dcp-7055, dcp-7060d, dcp-7065dn, mfc-7340, mfc-7360, mfc-7450, mfc-7840n, mfc-7860dn, mfc-7860dw, mfc-8460n, mfc-8860dn Content Feedback To help us improve our support, please provide your feedback below. After that, you must insert the toner cartridge (please refer to the toner cartridge replacement procedure, if you are installing a new toner cartridge) into the new drum unit until it clicks securely into place, and then install the new drum unit into the printer.
Drum near end on brother mfc 8860dn full#
Now, you must detach the toner cartridge from the exhausted drum unit by pulling it towards you while pushing down the blue lock release lever, but only if the toner cartridge is still useable (still contains toner), and then carefully take the new drum unit out of the protective packaging. Frequently occurring issues that affect Brother printers are: Paper jams Poor print quality Not turning on Laser not working Scanning issues Worn out drum unit Broken belt unit Waste toner box full Error message, code or number These are just some of the printer repairs carried out for businesses in the Buckinghamshire area. Please note that, you should avoid touching the electrodes on the inner sides of the printer, the contact area of the toner cartridge, and also the sensitive surface of the photoconductive drum, which is located on the top side of the new drum unit. Therefore, you must open the front cover, and then take the exhausted drum unit out of the printer by grabbing its front side and carefully pulling towards you. The drum unit installed in your Brother MFC-8860DN Multifunction Printer is located in the middle of the compartment behind the front printer cover. Important: You should follow the current replacement procedure strictly and avoid touching any printer components that are not listed in the instructions given below, because some of the components/parts surrounding the drum unit will be extremely hot. I still receive the error message 'Replace Drum', 'Drum End Soon', 'Drum Near End', or 'Drum Stop' after I replace the drum.